How to Pass a Smog Check: OBD2 Readiness Monitors Explained

You fixed the problem, cleared the check engine light, and headed straight to the emissions station. Then the inspector hands back a slip that says “not ready.” No failed test, no codes, just a rejection. It’s one of the most common and avoidable inspection headaches, and a basic OBD2 code reader can help you avoid it.
What Are Readiness Monitors?
Your vehicle’s computer runs a series of self-tests on emissions-related systems while you drive. Each self-test is called a monitor. When a monitor has run and finished its test, it’s marked “complete” or “ready.” If it hasn’t finished yet, it’s “incomplete” or “not ready.”
Common monitors include:
- Catalyst: checks catalytic converter efficiency.
- Oxygen sensor and oxygen sensor heater: check that the sensors respond correctly and warm up properly.
- Evaporative system (EVAP): checks for fuel vapor leaks.
- EGR or VVT system: checks exhaust gas recirculation or related systems, depending on the engine.
- Secondary air: on vehicles that use it.
- Misfire, fuel system, and comprehensive components: these “continuous” monitors run constantly and are usually ready quickly.
Diesel vehicles use a different set of monitors, including ones for the particulate filter and NOx systems.
Why Monitors Reset
Monitors go back to “not ready” when:
- You clear trouble codes with a scanner.
- The battery is disconnected or goes completely dead.
- Some computer updates or module replacements are performed.
This is why clearing codes right before an inspection is a bad idea. Even if you fixed the problem, the computer hasn’t proved it yet. And many inspection programs treat that as a reason to turn you away.
How Many “Not Ready” Monitors Are Allowed?
It depends on your state and the vehicle’s model year. A common rule in many U.S. programs is that 2001 and newer gasoline vehicles may have one incomplete monitor, while 1996–2000 vehicles may have two. Some states are stricter, some have special rules for certain monitors like EVAP, and rules change. Check your state’s emissions program website before you go.
How to Check Readiness Before Inspection
This is where a simple OBD2 tool pays for itself.
- Plug in your scanner with the ignition on.
- Open the I/M readiness screen. Tools like the Autel MaxiScan MS309 and AutoLink AL519 display readiness monitors. The AutoLink AL539B has a dedicated one-click I/M readiness key, which makes the check quick.
- Look for pending or stored codes. A clean readiness report doesn’t matter if a code is about to turn on the light.
- Count the incomplete monitors and compare with your state’s rules.
If everything is ready and there are no codes, you’re in good shape to test.
How to Get Monitors to Run: The Drive Cycle
Monitors complete when the vehicle sees the right conditions, which is called a drive cycle. Exact drive cycles vary by manufacturer, but a general pattern looks like this:
- Cold start. Let the car sit, ideally overnight, so the engine is fully cool.
- Idle for a few minutes with accessories off.
- Light acceleration to moderate speed, then steady cruising at a typical highway speed for several minutes.
- Deceleration without using the brake heavily, letting the vehicle coast down.
- Mixed city driving with stops and starts.
Some monitors have specific requirements. The EVAP monitor, for example, often needs a fuel level in a certain range (commonly between about a quarter and three-quarters of a tank) and specific ambient temperatures. If it won’t complete, check the fuel level first.
Realistically, normal mixed driving over several days completes most monitors. Check readiness each day with your scanner rather than guessing.
Tips for Stubborn Monitors
- Don’t keep clearing codes. Every clear starts the process over.
- Keep the fuel level in the middle range if EVAP is the holdout.
- Fix the underlying problem. A monitor that never completes can be a sign of a real fault, such as a thermostat stuck open that keeps the engine from warming up enough for some tests.
- Watch for pending codes. A pending code that keeps appearing is the computer warning you before the light comes on.
- Look up your vehicle’s specific drive cycle in the service information when general driving doesn’t work.
A Simple Pre-Inspection Checklist
- No check engine light on the dash.
- No stored or pending codes.
- Readiness monitors within your state’s allowance.
- No recent code clearing or battery disconnects.
- Engine fully warmed up when you arrive for the test.
Which Tool Should You Use?
For readiness checks, you don’t need an expensive tablet. A reliable code reader with an I/M readiness screen is enough. The MS309 is a compact, budget-friendly option, the AL519 adds live data and a sturdier handheld design, and the AL539B adds battery and charging tests. If you prefer your phone, the TOPDON TopScan Lite runs through a Bluetooth app. Compare them in our code readers category.
The Bottom Line
“Not ready” isn’t a failure, but it still costs you a trip. Check readiness with a scanner before you go, give the car time to complete its drive cycle after any repair, and avoid clearing codes right before the test. For a refresher on codes and freeze frame data, see our guide on how to read and clear a check engine light.





