Free Delivery on orders over $49.9. Don’t miss discount.

Blog

Scan Tool Service Functions Explained: Oil Reset, EPB, SAS, BMS, and More

Using a scan tool during brake service for electronic parking brake and service functions

Scanner spec sheets love to brag about “40+ service functions.” But what are they, and which ones will you actually use? Service functions are the routines a vehicle needs after normal maintenance: resetting, calibrating, or telling a module that a part has been replaced. On older cars you could do many of these with a button sequence. On newer vehicles, a scan tool is often the only practical way.

Here’s a plain-English look at the most common ones.

Oil Service Reset

What it does: Resets the oil life monitor or service reminder after an oil change.

When you need it: Every oil change. Some vehicles let you do this from the dash menu, but many, especially European models, either require a tool or make the manual procedure a guessing game.

Why it matters: Many oil life monitors calculate wear from engine conditions. If you don’t reset it, the reminder is meaningless and the light keeps nagging.

Electronic Parking Brake (EPB)

What it does: Puts the rear brake calipers into a service position so the pistons can be retracted, then brings them back and calibrates them after the job.

When you need it: Rear brake pad or rotor replacement on vehicles with an electronic parking brake.

Why it matters: On many EPB systems, forcing the piston back with a traditional tool can damage the caliper motor. Using service mode is the safe, correct approach.

Steering Angle Sensor (SAS) Calibration

What it does: Tells the stability control system where “straight ahead” is.

When you need it: After a wheel alignment, steering rack or column work, or some suspension repairs. Some vehicles also need it after a battery disconnect.

Why it matters: If the stability control system thinks the wheel is turned while you’re driving straight, it can set warning lights or, in some cases, intervene when it shouldn’t.

Battery Management System (BMS) Reset

What it does: Registers a new battery with the vehicle so the charging strategy matches the new battery’s condition, and on some vehicles its type and capacity.

When you need it: After replacing the battery on vehicles that use a BMS, which is common on European models and many newer vehicles with start-stop.

Why it matters: If the car thinks it still has an old, worn battery, it may charge the new one incorrectly and shorten its life. Our guide on how to test a car battery at home covers the testing side.

Throttle Body Relearn

What it does: Teaches the engine computer the closed position of the electronic throttle.

When you need it: After cleaning or replacing the throttle body, or sometimes after a battery disconnect.

Why it matters: A skipped relearn can cause high or unstable idle and stalling.

Diesel Particulate Filter (DPF) Regeneration

What it does: Commands the engine to burn off soot trapped in the DPF, and on some vehicles resets learned values after a filter replacement.

When you need it: On diesel vehicles when the DPF is clogging and normal driving hasn’t cleaned it, or after DPF-related repairs.

Why it matters: A badly clogged DPF can cut power and lead to expensive repairs. A forced regeneration should be done exactly as the tool and service information describe, because exhaust temperatures get very high.

Injector Coding

What it does: Enters the calibration code printed on a new injector so the engine computer can compensate for small manufacturing differences.

When you need it: After replacing injectors on many diesel and some direct-injection gasoline engines.

TPMS Relearn

What it does: Teaches the vehicle new or relocated tire pressure sensor IDs. We walk through it in detail in our TPMS relearn guide.

ABS Bleeding

What it does: Cycles the ABS pump and valves to push trapped air out of the hydraulic unit.

When you need it: After replacing an ABS unit or when air may have entered the ABS module during brake work.

Which Tool Covers What?

Service coverage depends on both the tool and the specific vehicle, so always check the coverage list. In general:

How to Choose

Make a short list of the jobs you actually do:

  • Oil changes and brakes at home? Look for oil reset and EPB support for your vehicles.
  • Alignment or suspension work? SAS calibration is a must.
  • Replacing batteries on newer cars? BMS registration matters.
  • Diesel owner? Check DPF and injector coding support carefully.

Then check that the tool covers those functions on your make, model, and year. A long service list is only useful if it includes the cars in your driveway or your bays.

The Bottom Line

Service functions are what turn a code reader into a real maintenance tool. You don’t need every function on the list, just the ones that match the work you do. Pick the tool that covers those jobs on your vehicles, and routine maintenance stops requiring a trip to the dealer.

Leave a Comment

Your email address will not be published. Required fields are marked *

Prove your humanity: 4   +   1   =  

Select your currency
Our customer support team is here to answer your questions. Ask us anything!