Kostenlose Lieferung bei Bestellungen über $49.9. Verpassen Sie nicht den Rabatt.

Der Blog

How to Diagnose a Crankshaft or Camshaft Position Sensor Code

Technician removing a crankshaft position sensor near the crank pulley

A crankshaft or camshaft position sensor code is one of the fastest tickets to a parts-store sensor that does not fix the car. The computer is telling you it lost a reliable position signal, or that the crank and cam no longer agree. That can be a failed sensor. It can also be oil in a connector, a rubbed harness, a damaged reluctor wheel, or a timing chain that has jumped. If you diagnose a crankshaft or camshaft position sensor code carefully, you decide whether you are replacing a sensor, repairing a circuit, or looking at mechanical timing — before the engine is left with a second no-start.

What these codes are actually reporting

The crankshaft position sensor (CKP) tells the computer where the crank is, and how fast it is turning. The camshaft position sensor (CMP) tells it where a cam is. The computer uses both to time fuel and spark, and to decide whether the valvetrain is still in step with the crank.

Circuit and signal codes — commonly in the P0335 family for the crank sensor and the P0340 family for a cam sensor, including intermittent variants — mean the signal was missing, implausible, or dropped out. Correlation codes, often in the P0016 family and its bank- or cam-specific cousins, mean both sensors appear to be working, but their relationship is not what the computer expects. That second group is where a stretched chain, a jumped tooth, a failed cam phaser, or a misinstalled sensor can hide behind a “sensor” label.

Symptoms range from a crank-no-start, to a long crank, a stall, a surge, or a misfire under load. Some engines will not inject or spark at all without a crank signal. Others start and then set a lamp when the signal glitches warm.

Capture the codes, then look at RPM and sync

Start with a full code and freeze-frame capture. Note whether the fault set during cranking, at idle, at cruise, or after a heat soak. A code that sets only when the engine is hot points you toward a heat-sensitive sensor or a swollen connector, not a cold-bay parts swap.

Then go to Live-Daten. A basic Bluetooth scanner such as TopScan is enough to watch RPM while cranking and, on many vehicles, cam and crank sync or CMP/CKP status PIDs.

If the engine cranks and RPM stays at zero, the computer is not seeing a crank signal. That is a no-start path, and our no-start diagnosis guide is the right companion. If RPM looks normal and a correlation code is stored, do not stop at the sensor. The computer already has a signal; it does not like the timing relationship.

Look at related codes too: cam-phaser, oil-control-valve, variable-valve-timing, and misfire codes often travel with a correlation fault. Those change the order of work.

Inspect the circuit and the target before you replace the sensor

Many “bad sensors” are oil-soaked connectors, backed-out terminals, or a harness that has rubbed through on a timing cover, a valve cover, or a bellhousing. Check power, ground, and the signal return at the connector with a reliable back-probe, and wiggle the harness while you watch the PID or a scope. An Inspektionskamera such as the Autel MaxiVideo MV480 helps you see a damaged connector or a cracked sensor boss in a tight valley or behind an intake.

Then think about the target the sensor reads. A reluctor wheel, tone ring, or vanes on a cam can be cracked, chipped, or packed with debris. A loose sensor, a missing spacer, or the wrong depth after a replacement can also weaken the signal. On some engines the crank sensor reads a ring on the converter or flexplate; a loose or damaged ring will set crank-sensor codes that a new sensor will not cure.

Know the sensor type. A two-wire magnetic sensor produces an AC voltage as the wheel turns. A three-wire Hall-effect sensor is usually a digital signal that needs a power supply. Testing one as if it were the other wastes time. Use the OEM check, not a generic “replace if it has any resistance.”

Use a scope when the signal is intermittent

Intermittent dropouts are hard to catch with a snapshot PID. An oscilloscope, such as the Autel MaxiScope MP608, lets you watch the crank and cam patterns together: amplitude, clean edges, missing teeth, and a dropout that appears only when you heat the sensor or move the harness. A pattern that collapses when the engine is hot, then returns when it cools, is a classic failing sensor or a poor connection. A clean pattern with the wrong phase between cam and crank is a timing or phaser problem.

You do not need a scope for every straightforward open-circuit failure. You do need one, or a very careful substitute test, before you condemn a sensor that only fails on a warm restart, or before you replace both sensors because a correlation code “sounds electrical.”

Do not confuse a sensor fault with a timing fault

If correlation is the stored code, measure actual mechanical timing the way the service information requires — marks, a camera on the chain, or a scan-tool timing PID that is known to be reliable on that engine — before you stack new sensors on a jumped chain. Low oil pressure, a stuck phaser, or a failed VVT solenoid can also shift a cam enough to set a correlation code.

When you do replace a sensor, use the correct cam versus crank part, the correct connector and fastener, and the specified air gap or dowel. Clear the codes, confirm RPM and sync at crank and at idle, then road-test, including a hot restart. Many vehicles need no formal relearn after a position-sensor replacement, but some do need a completed drive cycle and a confirmation that the monitor or the code has not returned. If the same code comes back immediately, the signal or the timing is still wrong.

A crankshaft or camshaft position sensor code is a signal diagnosis first and a parts decision second. Save the evidence, prove whether the computer has a signal, inspect the circuit and the reluctor, and only replace the sensor when the pattern or the circuit says that sensor is the failure. When crank and cam disagree, be willing to look at the chain.

Wählen Sie Ihre Währung
Unser Kundenservice beantwortet gerne Ihre Fragen. Fragen Sie uns alles!